View 4395A-1D5_4476523.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Agilent 4395A Network/Spectrum/Impedance Analyzer
Data Sheet
Network Measurement
Specifications describe the instrument's warranted performance over the temperature range of 0 C to 40 C (except as noted). Supplemental characteristics are intended to provide information that is useful in applying the instrument by giving non-warranted performance parameters. These are denoted as SPC (supplemental performance characteristics), typical, or nominal. Warm up time must be greater than or equal to 30 minutes after power on for all specifications. Source characteristics Frequency characteristics (Option 4395A-800) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Hz to 500 MHz Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 mHz Frequency reference Accuracy at 23 C 5 C, referenced to 23 C . . . . . . . . . . . . . . . . . . . . . . . . . . < 5.5 ppm Aging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 2.5 ppm/year (SPC) Initial achievable accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 1.0 ppm (SPC) Temperature stability at 23 C 5 C, referenced to 23 C . . . . . . . . . . . . . . . . . . . . . < 2 ppm (SPC) Precision frequency reference (Option 4395A-1D5) Accuracy at 0 C to 40 C, referenced to 23 C . . . . . . . . . . . . . . . . . . . . . . . . < 0.13 ppm Aging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0.1 ppm/year (SPC) Initial achievable accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0.02 ppm (SPC) Temperature stability at 0 C to 40 C, referenced to 23 C . . . . . . . . . . . . . . . . . . . < 0.01 ppm (SPC) Output characteristics Power range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 dBm to + 15 dBm Level accuracy at 0 dBm output, 50 MHz, 23 C 5 C, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 dB Level linearity Output power -40 dBm < -40 dBm Linearity1 1.0 dB 1.5 dB
1. At relative to 0 dBm output, 50 MHz, 23 C 5 C
Network Measurement
continued
Flatness at 0 dBm output, relative to 50 MHz, 23 C 5 C . . . . . . . . . . . . . . . . . . . . . . 2 dB Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 dB Spectral purity characteristics Harmonics at +10 dBm output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -30 dBc Non-harmonics spurious at +10 dBm output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -30 dBc Noise sidebands at 10 kHz offset from carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .< -95 dBc/Hz Power sweep range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 dB max. Power sweep linearity deviation from linear power referenced to the stop power level . . . . . . . . . . 0.5 dB Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 nominal Return loss frequency < 100 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .> 12 dB (SPC) frequency 100 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .> 7 dB (SPC) Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Type N female
2
Receiver Characteristics
Input characteristics Frequency range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Hz to 500 MHz Input attenuator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 50 dB, 10 dB step Full scale input level (R, A, B) Attenuator setting (dB) 0 10 20 30 40 50 Full scale input level -10 dBm 0 dBm +10 dBm +20 dBm +30 dBm +30 dBm
IF bandwidth (IFBW) 2, 10, 30, 100, 300, 1 k, 3 k, 10 k, 30 kHz Note: The IFBW should be set to less than 1/5 of the lowest frequency in the sweep range. Noise level (referenced to full scale input level, 23 C 5 C) at 10 Hz frequency < 100 Hz, IFBW = 2 Hz . . . . . . . . . . . . . . . . . . . . .-85 dB (SPC) at 100 Hz frequency < 100 kHz, IFBW = 10 Hz . . . . . . . . . . . . . . . . . . . . . . . . -85 dB at 100 kHz frequency, IFBW = 10 Hz . . . . . . . . . . . . . . . . . (-115 + f/100 MHz) dB Input crosstalk for input R + 10 dBm input, input attenuator:. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 dB for input A, B input attenuator: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 dB at < 100 kHz R through A, B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -100 dB others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -100 dB (SPC) at 100 kHz R through A, B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -120 dB others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -120 dB (SPC) Source crosstalk (for input A, B)(typical for input R) at + 10 dBm output, < 100 kHz, input attenuator: 0 dB . . . . . . . . . . . . . . . . < -100 dB at + 10 dBm output, 100 kHz, input attenuator: 0 dB . . . . . . . . . . . . . . . . < -120 dB Multiplexer switching impedance change at input attenuator 0 dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0.5% (SPC) at input attenuator 10 dB and above . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0.1% (SPC) Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Type-N female Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 nominal Return loss Input attenuator 0 dB 10 dB 20 dB to 50 dB 10 Hz frequency < 100 kHz 25 dB1 25 dB1 25 dB1 100 kHz frequency 100 MHz 25 dB1 25 dB 25 dB1 100 MHz < frequency 15 dB1 15 dB 15 dB1 Maximum input level Maximum safe input level +30 dBm (at input attenuator: 40 dB or 50 dB) +30 dBm or 7 Vdc (SPC)
1. SPC
3
Magnitude Characteristics
Absolute amplitude accuracy (R, A, B) at -10 dBm input, input attenuator: 10 dB, frequency 100 Hz, IFBW 3 kHz, 23 C 5 C, . . . . . . . . . . .< 1.5 dB Ratio accuracy (A/R, B/R) (typical for A/B) at -10 dBm input, input attenuator: 10 dB, IFBW 3 kHz, 23 C 5 C, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 2 dB Dynamic accuracy (A/R, B/R) (typical for A/B) Input level Dynamic accuracy1 (relative to full scale input level) frequency 100 Hz 0 dB input level > -10 dB 0.4 dB -10 dB input Level -60 dB 0.05 dB -60 dB > input level -80 dB 0.3 dB -80 dB > input level -100 dB 3 dB
Dynamic accuracy (dB)
Input level (dB)
Figure 1-1. Magnitude dynamic accuracy
Residual responses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .< -80 dB full scale (SPC) Trace noise (A/R, B/R, A/B) at 50 MHz, both inputs: full scale input level -10 dB, IFBW = 300 Hz . . . . . . . . . . . . . < 0.005 dB rms (SPC) Stability (A/R, B/R, A/B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0.01 dB/C (SPC) Phase characteristics Measurements format . . . . . . . . . . . . . . . . . . Standard format, expanded phase format Frequency response (deviation from linear phase) (A/R, B/R) (SPC for A/B) at -10 dBm input, input attenuator: 10 dB, IFBW 3 kHz, 23 C 5 C . . . . . < 12 Dynamic accuracy (A/R, B/R) (SPC for A/B) Input level Dynamic accuracy1 (relative to full scale input level) frequency 100 Hz 0 dB input level > -10 dB 3 -10 dB input Level -60 dB 0.3 -60 dB > input level -80 dB 1.8 -80 dB > input level -100 dB 18
1. R input level (B input level for A/B) = full scale input level -10 dB, IFBW = 10 Hz, 23 C 5 C
4
Dynamic accuracy (degree)
Input level (dB)
Figure 1-2. Phase dynamic accuracy Trace noise (A/R, B/R, A/B) at 50 MHz, both inputs: full scale input level -10 dB, IFBW = 300 Hz . . . . . . . . . . . . . . . . < 0.04 rms (SPC) Stability (A/R, B/R, A/B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .< 0.1 /C (SPC) Group delay characteristics Aperture [Hz] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.25% to 20% of span Accuracy In general, the following formula can be used to determine the accuracy, in seconds, of a specific group delay measurement: . . . . . . . . . . . Phase accuracy (degree) Aperture(Hz) x 360 (degree) Sweep characteristics Sweep type . . . . . . . . . . . . . . . . . Linear frequency, log frequency, power, list frequency Sweep direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Upper direction only Trigger type . . . . . . . . . . . . . . . . . . . . . . . . . Hold, single, number of groups, continuous Trigger source . . . . . . . . . . . . . . . . . . . . Internal (free run), external, manual, GPIB (bus) Event trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . On point, on sweep
5
Spectrum Measurement
Frequency characteristics Frequency range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Hz to 500 MHz Frequency readout accuracy SPAN[Hz] . . . . . . . . ((freq readout[Hz]) x (freq ref accuracy[1]) + RBW[Hz] + )) [Hz] NOP-1 where NOP means number of display points Frequency reference (Option 4395A-800) Accuracy at 23 C 5 C, referenced to 23 C . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 5.5 ppm Aging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 2.5 ppm/year (SPC) Initial achievable accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 1.0 ppm (SPC) Temperature stability at 23 C 5 C, referenced to 23 C . . . . . . . . . . . . . . . . . . . . . . . . < 2 ppm (SPC) Precision frequency reference (Option 4395A-1D5) Accuracy at 0 C to 40 C, referenced to 23 C . . . . . . . . . . . . . . . . . . . . . . . . . . < 0.13 ppm Aging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0.l ppm/year (SPC) Initial achievable accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0.02 ppm (SPC) Temperature stability at 0 C to 40 C, referenced to 23 C . . . . . . . . . . . . . . . . . . . . . . . < 0.01 ppm (SPC) Resolution bandwidth (RBW) Range 3 dB RBW at span > 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Hz to 1 MHz, 1-3 step 3 dB RBW at span = 0 . . . . . . . . . .3 k, 5 k, 10 k, 20 k, 40 k, 100 k, 200 k, 400 k, 800 k, 1.5 M, 3 M, 5 MHz Selectivity (60 dB BW/3 dB BW) at span > 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 3 Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auto or manual Accuracy at span > 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 10% at span = 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 30% Video bandwidth (VBW) Range at span > 0 . . . . . . . . . . . . . . . 3 mHz to 3 MHz, 1-3 step, 0.003 VBW/RBW 1 Noise sidebands (Carrier Frequency: 10 MHz, 100 MHz, 500 MHz) Offset from carrier Noise sidebands 1 kHz < -97 dBc/Hz 100 kHz < -110 dBc/Hz
Noise sideband (dBc/Hz)
Frequency offset (Hz)
Figure 1-3. Noise sidebands
6
Amplitude Characteristics
Amplitude range . . . . . . . . . . . . . . . . . . . . . . . . .displayed average noise level to +30 dBm Reference value setting range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -100 dBm to +30 dBm Level accuracy at -20 dBm input, 50 MHz, input attenuator: 10 dB, 23 C 5 C . . . . . . . . . .< 0.8 dB Frequency response at -20 dBm input, input attenuator: 10 dB, referenced to level at 50 MHz, 23 C 5 C frequency 100 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .< 1.3 dB frequency < 100 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .< 3.0 dB Amplitude fidelity1 Log scale2 Range Amplitude fidelity (dB to reference input lever [dB] [dB] 0 to -30 0.05 -30 to -40 0.07 -40 to -50 0.15 -50 to -60 0.35 -60 to -70 0.8 -70 to -80 1.8 Linear scale2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 3% Displayed average noise level at reference value -40 dBm, input attenuator: auto or 0 dB at frequency 1 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -120 dBm/Hz at 100 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -133 dBm/Hz at 10 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (-145 + frequency/100 MHz) dBm/Hz3
Average displayed noise (dBm/Hz)
F
(H )
Figure 1-4. Typical displayed average noise level
1. Fidelity shows an extent of nonlinearity referenced to the reference input level. 2. RBW = 10 Hz, -20 dBm reference value +30 dBm, reference input level = full scale input level -10 dB, 23 5 C 3. At start frequency 10 MHz Note: Refer to Input attenuator part for the definition of full scale input level.
7
On-screen Dynamic Range
On-screen dynamic range [dBc]
Offset frequency [Hz]
Figure 1-5. Typical on-screen dynamic range (center: 50 MHz)
Spurious responses Second harmonic distortion at single tone input with full scale input level -10 dB, input signal frequency 100 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -70 dBc Third order inter-modulation distortion at two tones input with full scale input level -16 dB, separation 100 kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -70 dBc Spurious at single tone input with full scale input level -10 dB, input signal frequency 500 MHz (RBW 100 kHz, 1 kHz frequency offset 300 MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < -70 dBc ( 60 dBc (SPC) if there are input signals in the following frequency range: (14.7 MHz to 15.9 MHz, 29.5 MHz to 31.7 MHz, 414.7 MHz to 415.9 MHz) Residual response at reference value setting -40 dBm, input attenuator: auto or 0 dB . . . . .< -108 dBm
8
Typical Dynamic Range
Third
Dynamic range (dB)
Second Sensitivity (1 Hz RBW) Sensitivity ( 100 Hz RBW) 2nd harmonic distortion 3rd order inter-modulation distortion
Input level (dB) (Relative to full scale input level)
Figure 1-6. Typical dynamic range at inputs R, A, and B
Input attenuator Setting range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 dB to 50 dB, 10 dB step Attenuator setting (dB) Full scale input level 0 -20 dBm 10 -10 dBm 20 0 dBm 30 +10 dBm 40 +20 dBm 50 +30 dBm Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auto or manual (In auto mode, the attenuator is set to minimum value which ensures full scale input level reference level.) Input attenuator switching uncertainty at attenuator: 30 dB, referenced to 10 dB . . . . . . . . . . . . . . . . . . . . . . . . . . . .< 1.0 dB at attenuator: 40 dB, referenced to 10 dB . . . . . . . . . . . . . . . . . . . . . . . . . . . < 1.5 dB Temperature drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0.05 dB/C (SPC) Scale Log 0.1 dB/div to 20 dB/div Linear at watt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 x 10-12 W/div at volt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 x 10-9 V/div Measurement format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spectrum or noise (/Hz) Display unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . dBm, dBV, dBV, V, W Sweep characteristics Sweep type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Linear, list Trigger type . . . . . . . . . . . . . . . . . . . . . . . . . .Hold, single, number of groups, continuous Trigger source . Internal (free run), external, manual, level gate, edge gate, GPIB (bus) Sweep time (excluding each sweep setup time) RBW SPAN Typical sweep time 1 MHz 500 MHz 180 ms 100 kHz 100 MHz 300 ms 10 kHz 10 MHz 240 ms 1 kHz 1 MHz 190 ms 100 Hz 100 kHz 270 ms 10 Hz 10 kHz 2.0 s 1 Hz 1 kHz 11 s -- Zero Span --1 9
1. See the next item for sweep time at zero span
Zero span RBW 5 MHz 100 kHz 3 kHz Minimum resolution 40 ns 1.28 s 40.96 s Maximum sweep time 1.28 ms 81.92 ms 2.62 s
Number of display points at span > 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 to 801 points (automatically set) at span = 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 to 801 points (selectable) Input characteristics Input port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R, A, B Crosstalk from any input to other inputs, at the same input attenuator settings < -100 dB (SPC) Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Type N female Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 nominal Return loss 0 dB 25 dB1 25 dB1 15 dB1 Input attenuator 10 dB 20 dB to 50 dB 25 dB1 25 dB1 25 dB 25 dB1 15 dB 15 dB1
10 Hz frequency < 100 kHz 100 kHz frequency 100 MHz 100 MHz < frequency
Input level . . . . . . . . . . . . . . . . . . . . . . . . . . . . +30 dBm max. at input attenuator: 50 dB Maximum safe input level . . . . . . . . . . . . . . . . . . . . . . . . . . . +30 dBm or 7 Vdc (SPC)
10
Specifications when Option 4395A-1D6 Time-Gated Spectrum Analysis is Installed
All specifications are identical to the standard Agilent 4395A except the following items.
Gate length Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 s to 3.2 s Resolution Range of gate length (TI) 6 s TI 25 ms 25 ms < TI 64 ms 64 ms < TI 130 ms 130 ms < TI 320 ms 320 ms < TI 1.28 s 1.28s < TI 3.2 s Resolution 0.4 s 1 s 2 s 5 s 20 s 100 s
Gate length Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8 s to 3.2 s Resolution Range of gate delay (Td) 0.8 s Td 25 ms 25 ms < Td 64 ms 64 ms

Additional amplitude error Log scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 0.3 dB (SPC) Linear scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 3% (SPC) Gate control modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . Edge (positive/negative) or level Gate trigger input (external trigger input is used) Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BNC female Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TTL Gate output Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BNC female Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TTL
11
Option 4395A-010 Impedance measurement
The following specifications are applied when the 43961A impedance test kit is connected to the 4395A.
Measurement functions Measurement parameters Display parameters Display formats * Vertical lin/log scale * Complex plane * Polar/Smith/admittance chart Sweep parameters * Linear frequency sweep * Logarithmic frequency sweep * List frequency sweep * Power sweep (in dBm unit)
Z, Y, L, C, Q, R, X, G, B, IZI, 0z, R, X, IYI, y, G, B, II, , x, y, Cp, Cs, Lp, Ls, Rp, Rs, D, Q
IF bandwidth * 2,10, 30, 100, 300, 1k, 3k, 10k, 30k [Hz] Calibration * OPEN/SHORT/LOAD 3 term calibration * Fixture compensation * Port extension correction Measurement port type * 7-mm Output characteristics Frequency range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 kHz to 500 MHz Frequency resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 mHz Output impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 nominal Output level when the measurement port is terminated by 50 1 . . . . . . . . . . . . . -56 to +9 dBm when the measurement port is open. . . . . . . . . . . . . . . . . . . 0.71 mVrms to 1.26 Vrms Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.1 dB Level accuracy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . frequency < 1 MHz -- (A + 3 [dB]) frequency 1 MHz -- (A + 1 [dB]) where, A is the sum total of level accuracy, level linearity and level flatness specifications for output characteristics of network measurement.
1. When the measurement port is terminated with 50 , the signal level at the measurement port is 6 dB lower than the signal level at the RF OUT port.
12
Measurement Basic Accuracy
(Supplemental performance characteristics)
Measurement accuracy is specified at the connecting surface of the 7-mm connector of the Agilent 43961A under the following conditions: Warm up time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 30 minutes Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 C 5 C, within 1 C from the temperature at which calibration is performed Signal level (setting) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to +15 dBm Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ON IFBW (for calibration and measurement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 Hz Averaging factor (for calibration and measurement) . . . . . . . . . . . . . . . . . . . . . . . . 8 At the following points, measurement error may exceed the performance described in this section: 124.0 MHz, 136.0 MHz, 415.0 MHz
Test frequency (Hz)
Figure 1-7. Impedance measurement accuracy IZI - accuracy IZI accuracy Z = A + (B/IZmI + C x IZmI) x 100 [%] accuracy = sin-1 (Z/100) Where, IZmI is IZI measured. A, B, and C are obtained from Figure 1-7. IYI - accuracy IYI accuracy Y = A + (B x IYmI + C/IZmI) x 100 [%] accuracy = sin-1 (Y/100) Where, IYmI is IYI measured. A, B, and C are obtained from Figure 1-7.
13
R - X accuracy (depends on D) Accuracy Ra Xa D 0.2 Xm x Xa /100[] Xa[%] 0.2 < D 5 Ra/cos[%] Xa/sin[%] 5Where, D can be calculated as: R/X, or R/(2f x Ls), or R x 2f x Cs can be calculated as: tan-1 (X/R), or tan-1 (2f x Ls/R), or tan-1 (1/(R x 2f x Cs)) Ra = A + (B/IRmI + C x IRmI) x 100 [%] Xa = A + (B/IXmI + C x IXmI) x 100 [%] Rm and Xm are the measured R and X, respectively. A, B, and C are obtained from Figure 1-7. G - B accuracy (depends on D) Accuracy Ga Ba D 0.2 Bm x Ba /100[S] Ba[%] 0.2 < D 5 Ga/cos[%] Ba/sin[%] 5Where, D can be calculated as: G/B, or G/(2f x Cp), or G X 2f x Lp can be calculated as: tan-1 (B/G), or tan-1 (2f x Cp/G), or tan-1 (1/(G x 2f x Lp)) Ga = A + (B/IGmI + C x IGmI) x 100[%] Ba = A + (B/IBmI + C x IBmI) x 100[%] Gm and Bm are the measured G and B, respectively. A, B, and C are obtained from Figure 1-7. D accuracy Accuracy Da Where, Za is IZI accuracy. L accuracy (depends on D) Accuracy La D 0.2 La 0.2 < D La (1 + D) D 0.2 Za/100 0.2 < D (Za/100) x (1 + D2)
Where, La = A + (B/IZlI + C x IZl) x 100[%] IZlI = 2f x Lm, f is frequency in Hz, and Lm is measured L. A, B, and C are obtained from Figure 1-7. C accuracy (depends on D) Accuracy Ca D 0.2 Ca 0.2 < D Ca (1 + D)
Where, Ca = A + (B/IZcI + C x IZcI) x 100[%] IZcI = (2 f x Cm)-1 f is frequency in Hz, and Cm is measured C. A, B, and C are obtained from Figure 1-7.
14
Common to Network/ Spectrum/ Impedance Measurement
Display LCD Size/type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.4 inch color LCD Number of pixels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640 x 480 Effective display area . . . . . . . . . . . . . . . . . . . . . . 160 mm x 115 mm (600 x 430 dots) Number of display channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Format single, dual (split or overwrite) Number of traces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . For measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 traces For memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 traces Data math . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . gain x data - offset, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . gain x (data - memory) - offset, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .gain x (data + memory) - offset, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . gain x (data/memory ) - offset Data hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maximum hold, minimum hold Marker Number of markers Main marker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .l for each channel Sub-marker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 for each channel marker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 for each channel Hard copy Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . Dump mode only (including color dump mode) Storage Built-in flexible disk drive Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 inch, 1.44 MByte, or 720 KByte, 1.44 MByte format is used for disk initialization Memory . . . . . . . . . . . . . . . . . . . . . . . . . . 512 KByte, can be backed up by flash memory GPIB Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IEEE 488.1-1987, IEEE 488.2-1987, IEC 625, and JIS C 1901-1987 standards compatible. Interface function . . . . . . . . . . . . . . . . . . . . . . . . SH1, AH1, T6, TEO, L4, LEO, SR1, RL1, PP0, DC1, DT1, C1, C2, C3, C4, C11, E2 Data transfer formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASCII, 32 and 64 bit IEEE 754 floating point format, DOS PC format (32 bit IEEE with byte order reversed) Printer parallel port Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IEEE 1284 Centronics standard compliant Printer control language . . . . . . . . . . . . . . . . . . . . . . . HP PCL3 printer control language Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-SUB (25-pin)
15
Option 4395A-001 DC voltage/current source The setting of Option 4395A-001 DC voltage/current source is independent of channel 1 and channel 2 settings. Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40 V to +40 V Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 mV Current limitation at voltage setting = -25 V to +25 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA at voltage setting = -40 V to -25 V, 25 V to 40 V . . . . . . . . . . . . . . . . . . 20 mA Current Range -20 A to -100 mA, 20 A to 100 mA Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 A Voltage limitation at current setting = -20 mA to +20 mA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 V at current setting = -100 mA to -20 mA, 20 mA to 100 mA . . . . . . . . . . . . 25 V Accuracy Voltage at 23 C 5 C . . . . . . . . . . . . . . . . . . . . . . (0.1% + 4 mV + Idc1 [mA] x 5 [] mV) Current at 23 C 5 C . . . . . . . . . . . . . . . . . . . . . (0.5% + 30 A + Vdc2 [V]/10 [k] mA) Probe power Output voltage . . . . . . . . . . . . . . . . .+15 V (300 mA), -12.6 V (160 mA), GND nominal Specifications when instrument BASIC is operated Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PS/2 style 101 English keyboard Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . mini-DIN 8 bit I/0 port Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-SUB (15-pin) Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TTL Number of input/output bit . . . . . . . . . . . . . . . . . . . . . . 4 bit for input, 8 bit for output
Figure 1-8. 8 bit I/O port pin assignments 24-bit I/O interface Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-SUB (36-pin) Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TTL I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-bit for input or output, 16-bit for output
Figure 1-9. 24-bit I/O interface pin assignment
1. Current at DC source connector. 2. Voltage at DC source connector.
16
Table 1-1. Signal source assignment
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
Signal name GND INPUT1 OUTPUT1 OUTPUT2 OUTPUT PORT A0 OUTPUT PORT A1 OUTPUT PORT A2 OUTPUT PORT A3 OUTPUT PORT A4 OUTPUT PORT A5 OUTPUT PORT A6 OUTPUT PORT A7 OUTPUT PORT B0 OUTPUT PORT B1 OUTPUT PORT B2 OUTPUT PORT B3 OUTPUT PORT B4 OUTPUT PORT B5 OUTPUT PORT B6 OUTPUT PORT B7 I/O PORT C0 I/O PORT C1 I/O PORT C2 I/O PORT C3 I/O PORT D0 I/O PORT D1 I/O PORT D2 I/O PORT D3 PORT C STATUS PORT D STATUS WRITE STROBE SIGNAL +5 V PULLUP SWEEP END SIGNAL
Signal standard 0V TTL level, pulse input (pulse width: 1 s or above) TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, latch output TTL level, input mode: LOW, output mode: HIGH TTL level, input mode: LOW, output mode: HIGH TTL level, active low, pulse output (width: 10 s; typical)
TTL level, active low, pulse output (width: 20 s; typical) +5 V +5 V, 100 mA MAX PASS/FAIL SIGNAL TTL level, PASS: HIGH, FAIL: LOW, latch output PASS/FAIL WRITE STROBE SIGNAL TTL level, active low, pulse output (width: 10 s; typical)
17
General Characteristics
Input and output characteristics External reference input Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 MHz 100 Hz (SPC) Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5 dBm to +5 dBm (SPC) Input impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 nominal Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BNC female Internal reference output Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 MHz nominal Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 dBm (SPC) Output impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 nominal Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BNC female Reference oven output (Option 4395A-1D5) Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 MHz nominal Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 dBm (SPC) Output impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 nominal Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BNC female External trigger input Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TTL Pulse width (Tp) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 s typically Polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . positive/negative selective Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BNC female External program Run/Cont input Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BNC female Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TTL Gate output (Option 4395A-1D6) Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TTL Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . BNC female
Positive trigger signal
Figure 1-10. Trigger signal (external trigger input)
Negative trigger signal
18
S-parameter test set interface Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-SUB (25-pin) Caution Do not connect a printer to this connector. If you connect a printer with the S-parameter test set interface connector (TEST SET-I/0 INTERCONNECT), it may cause damage to the printer.
Figure 1-11. S-parameter test set interface pin assignments
External monitor output Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-SUB (15-pin HD) Display resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640 x 480 VGA Operation conditions Temperature Disk drive non-operating condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 C to 40 C Disk drive operating condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 C to 40 C Humidity at wet bulb temperature 29 C, without condensation Disk drive non-operating condition . . . . . . . . . . . . . . . . . . . . . . . . . . 15% to 95% RH Disk drive operating condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15% to 80% RH Altitude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 2,000 m Warm up time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 minutes Non-operation conditions Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -20 C to 60 C Humidity at wet bulb temperature 45 C, without condensation. . . . . . . . . . . 15% to 95% RH Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 4,572 m Others EMC . . . . . . . . . . .Complies with CISPR 11 (1990) / EN 55011(1991) : Group 1, Class A Complies with EN 50082-1 (1992) / IEC 1000-4-2 (1995) : 4 kV CD, 8 kV AD Complies with EN 50082-1 (1992) / IEC 801-3 (1984) : 3 V/m Complies with EN 50082-1 (1992) / IEC 1000-4-4 (1995) :1 kV / Main, 0.5kV /Signal line Complies with IEC 1000-3-2 (1995) / EN 61000-3-2 (1995) Complies with IEC 1000-3-3 (1994) / EN 61000-3-3 (1995) Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Complies with IEC 1010-1 (1990), Amendment 1(1992), Amendment 2 (1995) Certified by CSA-C22.2 No.1010.1-92 Power requirements . . . . . . 90 V to 132 V, or 198 V to 264 V (automatically switched), 47 to 63 Hz, 300 VA max. Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 kg (SPC) Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425 (W) x 235 (H) x 553 (D) mm
19
Agilent Email Updates
www.agilent.com/find/emailupdates Get the latest information on the products and applications you select.
Remove all doubt
Our repair and calibration services will get your equipment back to you, performing like new, when promised. You will get full value out of your Agilent equipment throughout its lifetime. Your equipment will be serviced by Agilent-trained technicians using the latest factory calibration procedures, automated repair diagnostics and genuine parts. You will always have the utmost confidence in your measurements. Agilent offers a wide range of additional expert test and measurement services for your equipment, including initial start-up assistance, onsite education and training, as well as design, system integration, and project management. For more information on repair and calibration services, go to:
www.agilent.com/find/removealldoubt
www.agilent.com
For more information on Agilent Technologies' products, applications or services, please contact your local Agilent office. The complete list is available at:
www.agilent.com/find/contactus Americas Canada Latin America United States Asia Pacific Australia China Hong Kong India Japan Korea Malaysia Singapore Taiwan Thailand Europe & Middle East Austria Belgium Denmark Finland France Germany
Agilent Direct
www.agilent.com/find/agilentdirect Quickly choose and use your test equipment solutions with confidence.
(877) 894-4414 305 269 7500 (800) 829-4444
1 800 629 485 800 810 0189 800 938 693 1 800 112 929 0120 (421) 345 080 769 0800 1 800 888 848 1 800 375 8100 0800 047 866 1 800 226 008
0820 87 44 11 32 (0) 2 404 93 40 45 70 13 15 15 358 (0) 10 855 2100 0825 010 700*
*0.125 fixed network rates
01805 24 6333**
**0.14/minute
Ireland 1890 924 204 Israel 972-3-9288-504/544 Italy 39 02 92 60 8484 Netherlands 31 (0) 20 547 2111 Spain 34 (91) 631 3300 Sweden 0200-88 22 55 Switzerland (French) 41 (21) 8113811(Opt 2) Switzerland (German) 0800 80 53 53 (Opt 1) United Kingdom 44 (0) 118 9276201 Other European Countries: www.agilent.com/find/contactus
Revised: October 24, 2007
Product specifications and descriptions in this document subject to change without notice. (c) Agilent Technologies, Inc. 2001, 2003, 2007, 2008 Printed in USA, February 28, 2008 5965-9340E

▲Up To Search▲

Price & Availability of 4395A-1D5

	To Download 4395A-1D5 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .